|The Roller Wizard™ paint
roller cleaning system can be used during any stage of a painting project,
including freshening up the roller while painting, changing colors, and
cleaning up after the painting is finished! This system can be used anywhere
there is a water source with adequate drainage. Use with 9” long roller
sleeves and up to 1” nap. Box contains: tank, hose with 2 rubber washers
and faucet adapter. |
1. Attach the hose to Roller Wizard
manifold by turning brass fitting clockwise until tightly fitted (do not
over tighten). Make sure brass fitting contains washers to prevent water
leakage. (See Fig. 1)
2. Place the Roller Wizard in the
sink with the label towards you. Attach the faucet adapter to faucet by
first removing the faucet aerator on your sink. The faucet adapter included
will work with male or female threads. If this adapter does not work on
your particular faucet consult local hardware or home center for help.
(See Fig. 2) (Roller Wizard may also be used outside attached to a garden
Adapter Installation Hint:
Rotate adapter counter clockwise until you feel or hear a click, then turn
clockwise until tight.
3. With roller sleeve still on the
roller frame, open lid and insert roller frame into the hole from the front
(label side) of the Roller Wizard. (See Fig.3)
4. Rotate roller handle until it
fits into the notch on top of the tank and close lid. (See Fig. 4)
5. While holding the roller frame
in your left hand, turn on warm or cold water (do not use hot). Roller
frame must lay flat on the top and so that the roller sleeve does not hit
the inside of the Roller Wizard tank. (See Fig. 5)
6. Rotate manifold with your right
hand until roller sleeve spins. While roller sleeve is spinning, slowly
move manifold down to clean entire length of roller. Reverse sleeve spin
by rotating manifold in the opposite direction. Repeat up and down motion.
Continue cleaning in both directions until water is clear. (See Fig. 6)
7. For best results drying roller
sleeve, the sleeve must spin clockwise. Rotate manifold so the roller sleeve
is spinning clockwise as fast as possible. Maximum spin is achieved by
having the water spray just touching the outside of the roller sleeve.
With roller sleeve spinning, quickly rotate manifold counter-clockwise
to deflect water spray from roller sleeve. Wait for roller to stop spinning,
turn off water, open lid and remove roller. Roller sleeve will be slightly
damp and ready to store or use again. (See Fig. 7)
the Roller Wizard paint roller cleaning system into the sink with the front
label toward you, this will allow you to hold the paint roller in your
left hand and move the manifold with your right. If you wish to use your
right hand on the paint roller and the manifold with your left, turn the
tank so the front label is away from you. Practice to see which position
Read all instructions before using
Always wear eye protection (safety
Always use proper drainage - test
the drain with running water BEFORE attempting to use the Roller Wizard.
Local disposal requirements vary;
consult your sanitation depar tment or state designated environmental agency
for disposal options.
Hot Water is NOT recommended - it
will not decrease the cleaning process, and can damage the roller sleeve.
DO NOT use with oil-based paint.
Roller Wizard can only be used with Latex water-based paint.
Roller Wizard should only be connected
to a water supply with standard household water pressure.
Roller Wizard is intended for paint
removal from paint roller sleeve ONLY.
If temperatures are below freezing,
handle the Roller Wizard carefully - tank may crack in cold weather, especially
if dropped or hit against another object.
Manufacturer assumes no responsibility
for consequential or indirect damages or losses from the use of this product.
90 Day Limited Warranty
This warranty covers any defect
in material or workmanship for up to 90 days after the original purchase
of the Roller Wizard. We will replace the defective part or replace the
entire tool, at our discretion. To make a warranty claim: Call FPC Corp.
at 800-860-3838 for a Return Merchandise Authorization number (RMA).
NO WARRANTY CLAIM WILL BE HONORED
IF RMA IS NOT REQUESTED BEFORE ROLLER WIZARD IS SHIPPED TO FPC..
Properly pack the Roller Wizard
(in the original box, if possible), and clearly write the RMA number on
the outside of the box.
Include your receipt (original or
copy accepted), and the problem that you are having with the Roller Wizard.
Ship to FPC Corp., 355 Hollow Hill
Drive, Wauconda, IL 60084. Warranty DOES NOT COVER any damage from
misuse, abuse or neglect. FPC Corp.
expressly disclaims all responsibility for consequential or indirect damages
or losses caused by use of the product.